SWISS KRONO OSB/3 SF-B EN300 flameproof Stop Fire, square-edge,T + G – ContiFinish® - The classic product with built-in fire protection, Bonded without formaldehyde, CE, PEFCTM
SWISS KRONO OSB/3 SF-B is an enhancement of SWISS KRONO OSB/3, the well-known high-performance staple. Like it, the flame-retardant version is CE-certified under DIN EN 13986 and an ideal engineered wood product for loadbearing and reinforcing applications. The boards are completely impregnated with flame retardant to slow or prevent fires from starting, also after being worked and even at their corners and edges. This is a major advantage over other engineered wood products which merely have coated surfaces.
The benefits of OSB/3 SF-B:
- When exposed to flame, it chars to forms a fire-inhibiting layer.
- It reliably extinguishes without smouldering or continuously glowing.
- As the strands used to make it are treated as well, the edges of boards are also flame-retardant.
- It is as easy to saw, cut and otherwise work as standard OSB.
SWISS KRONO OSB/3 SF-B is mainly used in building construction for the substructures of exterior walls. Other applications include trade fair stands, halls, warehouses and similar structures.
Many large structures are used by large numbers of people, so the fire prevention requirements for them are especially demanding. Schools, nursing homes, clinics, government offices, factory and trade fair halls, and museums all require the use of building products with the ability to retard or resist flame.
SWISS KRONO OSB/3 SF-B not only meets the European fire protection requirements for public buildings, but also complies with the even stricter German standards. It has been assigned to reaction-to-fire performance class B-s1,d0 under EN 13501-1 (corresponding to B1), indicating that it fulfils the requirements for use in public buildings.
||Major axis||Minor axis|
|Nominal board thicknesses [mm]||d||12 - 18||> 18 - 22||12 - 18||> 18 - 22|
|Strength values [N/mm²]|
|Stresses on board||
|Stiffness values [N/mm²]|
|Stresses on board||
|Bending modulus of elasticity||Ema||4930||1980|
|Modulus of elasticity||Et/ca||3800||3000|
a The characteristic stiffness values E05 and G05 are calculated as follows:
E05 = 0.85 x E and G05 = 0.85 x G
|General and building physics values||
|Bulk density acc. to EN 323||m||700kg/m3|
|Max. deviations in board thickness||
± 0.8mm (ContiFinish®)
± 0.3mm (sanded)
|Tolerance in length and width||± 3mm|
|Perpendicularity acc. to EN 324‐2||2mm/m|
|Thermal conductivity acc. to EN 13986||λ||0.13W/mK|
|Water vapour resistance||sd||≥ 2.0m - dry (µ x d)|
|Waste code||EAK-Code||03 01 05|
|Thickness swelling acc. to EN 317||≤ 15%|
|Coefficient of expansion for 1% change in wood moisture content||0.03%|
E1 – 100% Formaldehyde-free binders
|Compliance with the Health Protection Requirements for Building Structures acc. with Annex 8 of the German Model Administrative Regulation on Technical Construction Requirements|
|Service classes acc. to EN V 1995-1-1||1 + 2|
|Reaction to fire acc. to EN 13501-1||B-s1, d0 - fire retardant|
|Burning / charring rate acc. to EN 1995-1-2||0.56mm/Min|
|Surface||crystalline efflorescence possible|
|Declaration of Performance No. acc. to CPR||SKDE_OSB-SF-B_CPR_2020_051|
Note: The characteristic values are for structural calculations acc. to EN 1995-1-1 and EN 1995-1-2 (EC5)
2500 x 1250 square-edge
3000 x 1250 square-edge
2500 x 675 T + G on all 4 edges
2500 x 1250 T + G on all 4 edges
Special formats and thicknesses on request
Laying and Boarding
- For interior or exterior boarding applications, leave expansion joints at least 3 mm wide between boards.
- When laid closely with butt joints in interior walls, leave room for expansion where the boards adjoin other structures.
- The storey-high formats are produced with a slightly reduced width (of 1247 mm) to allow for expansion.
Coating and Varnishing
- SWISS KRONO OSB with a ContiFinish® surface may be coated with a solvent-containing PU (DD) or synthetic-resin varnish.
- Sanded surfaces may be coated like normal wood (e.g. with varnishes, paints, oils, waxes and glazes).
- It is advisable to apply at least three coats, sanding after the first one.
- Application of at least three coats is recommended.
- The only way to achieve an absolutely smooth surface is to apply filler.
Transport and Handling
- Take steps to prevent the boards, and especially the unprotected edges, from absorbing large amounts of moisture during transport and installation. Be careful not to damage the edges when lifting, moving and stacking boards (this applies especially to tongue-and- groove boards).
- Check against the labels or producer’s documentation on-site to make sure that the following are correct: thickness, approved utilisation class, surface (sanded or ContiFinish®) and edge type (square-edged or tongue-and-groove).
- During installation, boards may be briefly leaned against a solid structure at a 70° angle.
- Always carry individual boards in an upright (vertical) position.
- Protect boards from exposure to significant moisture or very high relative humidity.
- Prevent direct contact of the boards with the floor. ■ Only store outdoors temporarily, and if unavoidable cover stacks with watertight but water-vapour-permeable tarpaulins.
- Always stack boards horizontally on pallets and wooden supports (spaced no more than 600 mm apart).
- Align wooden supports precisely with one another and parallel to the shorter side of the boards.
- Lay the boards so their edges line up (with a maximum overhang of 15 mm).
- Precondition boards prior to installation.
- Store boards for about three days under the same climatic conditions that prevail at the installation site.
- This adjustment to the ambient moisture at the installation site will prevent excessive shrinkage or swelling.
Sawing, Milling, Sanding and Drilling
- SWISS KRONO OSB can be sanded, sawn, milled and drilled just like solid wood and using all of the same tools.
Nailing, Stapling, Screwing and Gluing
- SWISS KRONO OSB can be attached to wooden studs and rafters using screws, nails or staples.
- Use in accordance with the official approvals and standards (Z-9.1-618, Z-9.1-503 and DIN 1052 in Germany as well as EN 1995-1-1 (EC 5)).
- Additionally bond or glue tongue-and-groove joints.
Documents à téléchargerRubrique:
Aucune rubrique %1n’a été trouvée. Veuillez sélectionner une autre rubrique et/ou une autre langue.
Vous trouverez les rubriques qui ne correspondent pas au choix de langues proposé (allemand, anglais, français, russe, espagnol) dans la catégorie « Autres ».
Pour un aperçu rapide, sélectionnez « Liste complète » pour obtenir un aperçu de toutes les langues et de toutes les versions d’une rubrique.